COMPUTER FLAT KNITTING MACHINE OPERATION AND MAINTENANCE METHODS

A, computerized flatbed operation precautions

(1) Read the disk, when it is not smooth, you can turn off the power again after plugging the USB socket, with the controller can first switch the storage and reading media (U disk and disk) and then turn on the machine to read the disk.

(2) wear yarn, and at the same time to adjust the antenna elasticity, side antenna tension.

(3) To adjust the degree of mesh, tension, etc. in accordance with the proofing requirements.

(4) Determine the position of pattern unfolding and yarn nozzle placement.

(5) hanging cloth (starting the bottom plate machine without), line lock (machine with repeat) instantly to the vice Lola open and close the situation, the machine head speed to be less than 0.40m / s, the cloth reaches the main Lola lift line lock, increase the speed, tension, etc.

B, the computerized flat knitting machine began to knit

(1) at any time to check the density of the cloth and to confirm the coarse and young yarn situation, in order to control the length of the piece of clothing at any time. Follow the size of the sample.

(2) pay attention to the wool yarn over wax and wool yarn discharge position. (2) To re-test the yarn and tensile strength when removing the piece.

(3) Keeping abreast of the yarn situation and wool color difference.

(4) The pieces are divided into yards and colors and folded neatly, and delivered in bundles as required.

(5) Pay attention to rewind cloth and vice roller yarn winding.

C, the computerized flat knitting machine common problems handling methods

1, Measurements

(1) knitting degree of the eye increasingly large.

(2) two ports at the same time to do knitting, if a mouth degree of purpose abnormally small, you can consider the degree of purpose of the original point of appropriate adjustment.

2, connecting stitches

(1) to see if the degree of flexibility.

(2) to see if the connected stitches in the needle bed is running smoothly, whether the hand pressed down to pop up freely.

(3) check whether the motor screw of the degree eye is loose. (3) check whether the motor screws are loose.

(4) Check for damage to the eye sensor.

(5) Check if the three feet of the flat knitting machine presser are in place.

(6) When the degree eye is too tight, it cannot be taken off the loop and will also hit the connecting stitch.

(7) Check whether the needle guide block of the needle flip triangle is smooth and flexible.

(8) check whether the bottom plate of the degree eye, the slider is in place, flexible.

3, chaotic flowers (chaotic needle selection)

(1) to see whether the fabric piece of disorderly flowers are regular, such as the problem are in which a needle selector.

(2) to see whether it is stolen or missed selection, adjust the gap between the needle selection piece and the needle bed.

(3) adjust needle selection parameters, needle selection origin, needle selection fine-tuning.

(4) to see if the needle selection pin on the needle bed is too tight, too loose, whether smooth.

(5) line check, whether the plugs are plugged in, to see if there is poor contact.

(6) to see if the main drive belt is too loose.

(7) to see if the lower needle ruler will be too tight or too loose.

(8) replace the needle selection substrate.

(9) re-find the origin.

4, flat rocking needle leakage

(1) to see if the chaotic flowers caused by.

(2) to see if the installation of the sky rod is standardized, may lead to the yarn mouth high and low, whether the alignment of the mouth hole in the seam.

(3) to see if the knitting needle is not smooth in the needle bed.

(4) to see if the last row of turning needles left behind.

(5) to see if the knitting needle is damaged.

5, slanting piece

(1) If the flat knitting machine slant piece in the determination is not the reason for the tension, wool yarn placement, the long side of the piece of cloth needle plate down, the short side of the needle plate up.

(2) Special cases can be considered for moving the guide rail.

(3) The above two practices should take into account the "needle turning position".